Whenever you start facing issues with your mesh system, you can reset the Velop to fix it. Therefore, knowing the process to factory reset Linksys Velop can be beneficial. However, the reset restores the factory default settings of the Velop. So, the reset should be one’s last resort, as you shouldn’t have to reset the Velop after every minor inconvenience. Additionally, the Linksys Velop reset can only fix the internal issues within the Velop. If the issue exists due to external factors, the reset cannot resolve those problems.

Therefore, before you reset the Linksys Velop, you must figure out the issue. If you want to know the Linksys Velop factory reset process, we’ve got you! Today, we’ll discuss the complete reset procedure.

Why Do I Need to Reset My Linksys Velop?

There are several factors responsible for when Linksys Velop starts facing issues. The Linksys Velop could face internal as well the external problems. To resolve the internal issues, executing the Linksys Velop factory reset is crucial. The factory reset fixes all the internal glitches and restores Velop’s factory default settings. After the reset, the Velop will be as good as new. Therefore, it’s a must for the users to know Linksys velop reset.

Factory Reset Linksys Velop

There are two ways for the Linksys Velop reset. You can either reset the Velop manually or through the user interface. The procedure for both these methods are as follows:

Manual Linksys Velop Factory Reset through Button

• Initially, turn ON the router and ensure the power LED is ON.
• Secondly, find the reset button on the router.
• Now, press the reset button and hold it for a few seconds.
• When the router starts flashing red light, you can release the button.
• The reset is successful.
• Now, you can reconfigure the Velop.

Web-based Linksys Velop Reset

• To begin with, log into the user interface.
• You can log into the user interface through the Linksys app.
• Now, from the home page, go to ‘Troubleshooting’ from the Router Settings.
• After that, navigate to the ‘Diagnostics’ tab.
• Under ‘Factory Reset, click the Reset link to initiate the reset.
• At last, tap ‘Yes’ to reset the Velop system.

That’s it! These are the steps to factory reset Linksys Velop. Now, you can set up your Linksys Velop again.

How to Reconfigure Linksys Mesh After Reset?

As we know, after the factory reset Linksys Velop, the default settings will be back. This means that every change and customization made by you will be gone. The Linksys Velop will forget every device connected to the router. Therefore, you will have to set up the Linksys Velop again. The steps are as follows:

• Primarily, place the main router, and the nodes in the same room.
• Download the Linksys Velop from Play Store or App Store on your mobile device.
• Now, connect the main node to your modem using an Ethernet cable and power it ON.
• Ensure the power LED is blinking purple on the main node.
• After that, open the app, and click Set up a New WiFi Network.
• Hereon, follow the instructions you will receive from the app.
• The app will assist you through the whole procedure thoroughly.
• Once, you are done with the setup, you can plug the nodes in the desired location.
• After that, the LED light on the nodes will turn blue.
• Ensure to place the nodes in the most suitable location to maximize their benefit.
• At last, you can connect your devices to their network, and check the network.

These are the steps to reconfigure the Linksys Velop after the Linksys Velop factory reset.

FAQs

Do I Need to Login to Reset My Velop System?

Not necessarily. You can proceed with the Linksys Velop reset manually as well. Additionally, you can reset the Velop through the user interface of the Velop as well. To reset the Velop through the admin panel, you will have to log in to Linksys velop.

Can I Reset Only Child Nodes?

If you reset just the child nodes, you will have to reset the main router as well. The procedure to factory reset Linksys Velop child nodes, follow the steps below:

• To begin with, open the Linksys Velop app.
• From the admin panel, go to the ‘Velop Administration’ section.
• Now, choose the child node you want to reset.
• After that, tap the ‘Node’ button and choose the ‘Advanced’ settings.
• Hereon, go to the bottom and select the ‘Reset Node’ option.
• At last, you can follow the prompts to confirm the reset.

The reset is successful.

Do I Need to Create a New Account After Resetting the Device?

No, the Linksys Velop factory reset will not delete your cloud account. It will only erase the customizations and changes made by you. Your Linksys cloud account will be just fine.

We hope you understood the Linksys Velop reset procedure. If there are any difficulties you are having with your Linksys Velop, you can get in touch with our team now!